View source for Quick Memory

==General==
The bottom two lines of the '''[[Misc]]''' form are a set of controls that allow saving up to five (5) sets of radio frequency data. Hovering the cursor over a control will display the control function. See below for more description.

[[image:QuikMem.png]]

==Features==
* Non-persistent five (5) position LIFO (Last In First Out) memory buffer holding the following data.
** '''VFO A''' frequency
** '''VFO B''' frequency
** '''TX VFO''' (A/B)
** '''Mode'''
** '''RX1 Antenna'''
** '''RX2 Antenna'''
** '''TX Antenna'''
** '''TX Line''' (TX1-3)
** '''RX Filter'''
** '''TX Profile'''
* '''Recall''' & '''Load''' memory data as needed
* '''Clear''' all memories
* '''VFO <> Memory''' swap
** Toggles current VFO A frequency, RX filter and mode with the selected memory slot.

==Controls==
*'''V<>M''' - Exchanges VFO and selected memory data (toggle).
*'''ReCall''' - Pressing this button repeatedly displays frequency, mode and memory number for each of the five (5) memories.
*'''Load''' - Sends selected memory data to '''PowerSDR'''.
*'''Save''' - Saves current frequency and profile data to #1 memory slot.
*'''Clear''' - Erases all memory data.

===Memory Note===
As a way to attach a reminder note to the memory slot displayed the following method is available.
* '''Double-Click''' the '''Frequency''' window just below the '''ReCall''' button.
** Alternately, press the '''[Ctrl + N]''' keys to open the '''Memory Note''' window.
[[image:MemoryNote.jpg]]
* Fill in the note text as desired and press OK.
* The '''Memory Note''' will be stored with the memory information and recalled and displayed with the memory data.
* '''Display'''
** The '''Memory Note''' is displayed in the title bar of the '''Misc''' form.

==Operation==
'''''<font size="3" color="red">Notice!</font>''''' - 
This is '''volatile''' (non-persistent) memory. It lasts '''ONLY''' for the current '''DDUtil''' operating session.
===Storing Memory Data===
* Tune to frequency to be remembered.
* Press the '''ReCall''' button to select the desired memory slot to store the data.
* Press '''Clear''' if not empty.
* Press the '''Save''' button.
* Button will blink Yellow when frequency and mode data are saved.
'''''<font size="2" color="red">Alert!</font>''''' - 
If the memory slot selected is not empty memory slots 2-4 will be pushed down one level and the new data will be stored in slot #1.
===Recalling Memory Data===
* Press the '''ReCall''' button to select the desired memory slot.
** Repeatedly pressing in the '''ReCall''' button will page (rotate) through the five (5) memory slots.
* Press the '''Load''' button to send the save memory data to radio.
'''''<font size="2" color="red">Alert!</font>''''' - 
Pressing the '''Load''' button will replace current frequency and mode data in the radio. If you want to preserve the current radio frequency position use the '''V<>M''' button feature instead (see below).
===Clearing Memory Data===
* Press the '''Clear''' button to clear the selected memory slot.
* Pressing the key combination of '''Ctrl+Shift+Clear''' will clear all memory slots.
===Exchange VFO & Memory Data===
This feature allows you to move the radio to one of the stored memory frequencies without losing your current VFO frequency location. And then move back to where you came from when ready.
* Press the '''V<>M''' button.
** The '''V<>M''' button will turn '''Yellow'''.
** The current '''VFO''' frequency will display in the window below the '''V<>M''' button.
** The radio will move to the frequency of the selected memory.
* Press the '''V<>M''' button again.
** The radio will be returned to it's previous VFO frequency.
** The '''V<>M''' button back ground color will return to normal.
** The VFO frequency display below the '''V<>M''' button will be blank.