Difference between revisions of "RCP Redirect"
From DDUtilV3
m (WikiSysop moved page RcpRedirect to RCP Redirect without leaving a redirect) |
|||
| (3 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | The '''RCP Redirect''' function allows '''Flex 6000''' users the ability to re-assign other Radio Slices ' | + | The '''RCP Redirect''' function allows '''Flex 6000''' users the ability to re-assign other Radio Slices '''B' - 'H''' (per radio ability) for four of the [[Glossary#Radio_Control_Program|'''RCP''']] ports (3,4,5,6). This re-direction has the following properties/restrictions. |
| + | |||
| + | ==Restrictions== | ||
| + | * Only works for the '''F6000''' radios. | ||
* Only the '''Kenwood''' radio type is supported. Other radio types '''CAT''' commands are not recognized. | * Only the '''Kenwood''' radio type is supported. Other radio types '''CAT''' commands are not recognized. | ||
* Only '''VFO A''' is supported. | * Only '''VFO A''' is supported. | ||
| − | * '''Split''' operation '''IS NOT''' supported for re-assigned slices. Slice '''TX''' must be selected manually on the ''' | + | * '''Split''' operation '''IS NOT''' supported for re-assigned slices. Slice '''TX''' must be selected manually on the '''SmartSDR GUI'''. |
| − | * '''Frequency''' and '''Mode''' may be assigned by the '''RCP''' software | + | |
| + | ==Properties== | ||
| + | * '''Frequency''' and '''Mode''' may be assigned by the [[Glossary#Radio_Control_Program|'''RCP''']] software. | ||
| + | ** Double-clicking a '''Telnet Spot''' entry will '''QSY''' the re-assigned slice's frequency and set it's mode. | ||
| + | ** Changing frequency and/or mode in an [[Glossary#Radio_Control_Program|'''RCP''']] program will adjust the slice accordingly. | ||
| + | |||
| + | ==Use== | ||
| + | * In '''DDUtil''' (Ports Tab | RCPs group), connect one end of a '''Virtual Serial Port''' pair to one of the [[Glossary#Radio_Control_Program|'''RCP''']] ports (RCPs 3,4,5,6 only). | ||
| + | * Open the Cat port configuration section of the selected [[Glossary#Radio_Control_Program|'''RCP''']] and connect the other end of the port pair that was connected to '''DDUtil''' in the above step. | ||
| + | * Verify the [[Glossary#Radio_Control_Program|'''RCP''']] is following the radio. | ||
| + | * In '''DDUtil''' (Ports Tab | RCP ReDirect group) find the matching drop-down box and select the radio slice you would like to use for the [[Glossary#Radio_Control_Program|'''RCP''']] you setup above. | ||
| + | * The frequency of the [[Glossary#Radio_Control_Program|'''RCP''']] should change to agree with the new slice frequency. | ||
Latest revision as of 12:01, 24 July 2013
The RCP Redirect function allows Flex 6000 users the ability to re-assign other Radio Slices B' - 'H (per radio ability) for four of the RCP ports (3,4,5,6). This re-direction has the following properties/restrictions.
Restrictions
- Only works for the F6000 radios.
- Only the Kenwood radio type is supported. Other radio types CAT commands are not recognized.
- Only VFO A is supported.
- Split operation IS NOT supported for re-assigned slices. Slice TX must be selected manually on the SmartSDR GUI.
Properties
- Frequency and Mode may be assigned by the RCP software.
- Double-clicking a Telnet Spot entry will QSY the re-assigned slice's frequency and set it's mode.
- Changing frequency and/or mode in an RCP program will adjust the slice accordingly.
Use
- In DDUtil (Ports Tab | RCPs group), connect one end of a Virtual Serial Port pair to one of the RCP ports (RCPs 3,4,5,6 only).
- Open the Cat port configuration section of the selected RCP and connect the other end of the port pair that was connected to DDUtil in the above step.
- Verify the RCP is following the radio.
- In DDUtil (Ports Tab | RCP ReDirect group) find the matching drop-down box and select the radio slice you would like to use for the RCP you setup above.
- The frequency of the RCP should change to agree with the new slice frequency.
